AUX E&H Series Instrucciones de operaciones Pagina 27
- Pagina / 92
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5.1 Start-up
After switching the instruement on, make the following settings to the specified function groups:
• Function group SERVICE (S)
S1: Select language and exit function
group.
• Function group SETUP 1 (A)
Adjust all the parameters in this group, see
chapter 5.2.1.
• Function group SETUP 2 (B)
Make all settings in this group, see
chapter 5.2.2.
Other configuration options are explained in
the chapters to follow for each menu.
5.2 System configuration
The system is configured using the function groups SETUP 1 and SETUP 2. The measurement
type and electrode are selected here, and the settings for the temperature measurement are
made. All the parameters in these two function groups are to be configured to avoid measuring
errors or failure to measure at all.
5.2.1 Setup 1 (pH / Redox)
For access to the SETUP menu, please enter Code 22.
Coding Field
Selection or range
Factory setting (bold)
Display Info
A
Function group
SETUP 1
Initial display in function group
SETUP 1.
A1
Operating mode
selection
pH
ORP ( = Redox) mV
ORP ( = Redox) %
Any change in operating mode
causes an automatic reset of
basic settings.
A2 Select display unit
pH
mV
%
A3
Select connection
mode
sym = symmetrical
asym = asymmetrical
See chapter 3.
A4
Enter measured
value damping
1
1...60
Measured value damping causes
averaging over the specified
number of individual measured
values and is used e. g. to
stabilise the display and the
signal output. There is no
damping if “1" is entered.
Factory settings are printed in bold face;
base version does not include functions in
italic
.
A
SETUP 1
pH A1
Oper.Mode
pH
A2
Unit
sym
A3
wiring
1
A3
Damping
PM253E5A.CHP
Liquisys M CPM 223 / 253 Instrument configuration
Endress+Hauser 25
- Endress Hauser 1
- Table of contents 3
- 1 General information 4
- 1.5 Product structure 5
- 2 Safety 6
- 2.5 Immunity to interference 7
- 2.6 Declaration of conformity 7
- 3 Installation 8
- 3.2 Dimensions 9
- 3.3 Mounting 10
- PM253E03.CHP 11
- 3.3.2 Mounting examples 12
- Endress+Hauser 11 13
- 3.4 Electrical connection 14
- 131094-4G 15
- Construction of special 16
- CPK1_12e.EPS 16
- Fig. 3.13 16
- • If the software setting 18
- Setpoint 19
- 4.3 Keys 20
- PM253ED4.CHP 21
- 4.5 Operating concept 22
- 4.5.2 Access codes 23
- 4.5.3 Menu structure 23
- • If a change is made but not 23
- • See the appendix of these 23
- 5 Instrument configuration 25
- RELAY2.CDR 26
- Oper.Mode 27
- Glass A5 28
- Fig. 5.4 29
- Alarm signalling and 29
- 28 Endress+Hauser 30
- PM253E5A.CHP 31
- Fig. 5.7 32
- User-defined current output 32
- Sel. Out2 33
- Tabelle (3) 34
- Table (3) 34
- 5.5 Monitoring functions 35
- Rel.Assg 36
- Curr.Assg 36
- CleanTrig 36
- 5.5.2 Check 37
- • Due to its semiconductor 37
- A.Thresh 38
- Err.Delay 38
- LowAlarm 38
- HighAlarm 39
- ProcMonit 39
- Tmax Low 39
- Tmax High 39
- GRENZ-E.CDR 40
- not allowed 41
- Pulse length modulation 42
- Pulse frequency modulation 42
- PM253E5B.CHP 43
- 5.6.4 ChemoClean function 44
- • Use relays 3 (water) and 44
- • When “Economy” is selected 44
- LC PV R2 45
- LC State 46
- 120 R239 48
- 0.3 R2310 48
- Clean = ChemoClean (5) 49
- Neutra controller (6) 49
- ChemoClean (5) 49
- Proc.Type 51
- 5.7 Service 52
- S.Default 53
- Contr E1 54
- SerNo E113 54
- LSG E114 54
- 5.10 Calibration 55
- the user is 55
- ≤ 0.05 and value 56
- 59.18 N2 59
- PV Offset 60
- 6 Interfaces 61
- Endress+Hauser 61 63
- 62 Endress+Hauser 64
- Endress+Hauser 63 65
- 64 Endress+Hauser 66
- Endress+Hauser 65 67
- 8.1 Diagnosis 68
- Endress+Hauser 67 69
- 223EXPHE.CDR 70
- 8.2.2 Disassembly of CPM 223 71
- 8.2.3 Assembly of CPM 223 71
- 8.2.4 Spare parts for CPM 223 72
- 253EXPHE.CDR 73
- 8.3.2 Disassembly of CPM 253 74
- 8.3.3 Assembly of CPM 253 74
- 8.3.4 Spare parts for CPM 253 75
- 8.4 Spare parts orders 76
- 8.6.1 pH/redox transmitter 77
- 8.6.2 pH/mV electrodes 77
- 8.6.3 Assembly 77
- 8.6.4 Liquid KCl supply 77
- 9 Accessories 79
- 10 Technical data 81
- 80 Endress+Hauser 82
- Endress+Hauser 81 83
- 11 Appendix 84
- Endress+Hauser 83 85
- 84 Endress+Hauser 86
- Endress+Hauser 85 87
- 12 Index 88
- PM253E12.CHP 89
- Declaration of contamination 91
- BA 194C/07/en/07.02 92
- Printed in Germany / CV5 / DT 92
Relacionado con productos y manuales para Acondicionadores de aire del sistema de división AUX E&H Series
(15 paginas)
(19 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales