AUX E&H Series Instrucciones de operaciones Pagina 74
- Pagina / 92
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
8.3.2 Disassembly of CPM 253
• Open and remove the connection
compartment cover (Pos. 420).
• Pull out the mains terminal (Pos. 470) to
make the device voltage-free.
• Open the display cover (Pos. 410) and
loosen the ribbon cable (Pos. 310 / 320) on
the side of the electronics box (Pos. 330).
• Dismantling the controller (Pos. 40):
Loosen screw (Pos. 450b) in the display lid.
• Removal of electronics box (Pos. 330):
Loosen screws (Pos. 450a) in the bottom of
the housing 2 revolutions, then slide entire
box backward and remove towards the top.
Make absolutely sure that the module locks
do not open!
Bend the module latches outward and
remove the module(s).
• Dismantling the docking module (Pos. 340):
Loosen screws (Pos. 450c) in the bottom of
the housing and remove entire module
towards the top.
• Dismantling the pH/mV Transmitter
(Pos. 230):
– Bend the screen plate upward
– Pull off the stranded wire (plug-in
connection; pH input from BNC socket),
then pull off the module towards the top.
8.3.3 Assembly of CPM 253
• Insert the module(s) in the electronics box
guide rails carefully and latch into the
lateral lugs in the box.
• Incorrect assembly is not possible!
Modules incorrectly inserted into the
electronics box can not be put into
operation because the ribbon cables can
not be plugged in if this is the case.
• Make sure that the cover gaskets are intact
since they are required to guarantee
protection class IP 65.
Diagnosis and corrective maintenance Liquisys M CPM 223 / 253
72 Endress+Hauser
- Endress Hauser 1
- Table of contents 3
- 1 General information 4
- 1.5 Product structure 5
- 2 Safety 6
- 2.5 Immunity to interference 7
- 2.6 Declaration of conformity 7
- 3 Installation 8
- 3.2 Dimensions 9
- 3.3 Mounting 10
- PM253E03.CHP 11
- 3.3.2 Mounting examples 12
- Endress+Hauser 11 13
- 3.4 Electrical connection 14
- 131094-4G 15
- Construction of special 16
- CPK1_12e.EPS 16
- Fig. 3.13 16
- • If the software setting 18
- Setpoint 19
- 4.3 Keys 20
- PM253ED4.CHP 21
- 4.5 Operating concept 22
- 4.5.2 Access codes 23
- 4.5.3 Menu structure 23
- • If a change is made but not 23
- • See the appendix of these 23
- 5 Instrument configuration 25
- RELAY2.CDR 26
- Oper.Mode 27
- Glass A5 28
- Fig. 5.4 29
- Alarm signalling and 29
- 28 Endress+Hauser 30
- PM253E5A.CHP 31
- Fig. 5.7 32
- User-defined current output 32
- Sel. Out2 33
- Tabelle (3) 34
- Table (3) 34
- 5.5 Monitoring functions 35
- Rel.Assg 36
- Curr.Assg 36
- CleanTrig 36
- 5.5.2 Check 37
- • Due to its semiconductor 37
- A.Thresh 38
- Err.Delay 38
- LowAlarm 38
- HighAlarm 39
- ProcMonit 39
- Tmax Low 39
- Tmax High 39
- GRENZ-E.CDR 40
- not allowed 41
- Pulse length modulation 42
- Pulse frequency modulation 42
- PM253E5B.CHP 43
- 5.6.4 ChemoClean function 44
- • Use relays 3 (water) and 44
- • When “Economy” is selected 44
- LC PV R2 45
- LC State 46
- 120 R239 48
- 0.3 R2310 48
- Clean = ChemoClean (5) 49
- Neutra controller (6) 49
- ChemoClean (5) 49
- Proc.Type 51
- 5.7 Service 52
- S.Default 53
- Contr E1 54
- SerNo E113 54
- LSG E114 54
- 5.10 Calibration 55
- the user is 55
- ≤ 0.05 and value 56
- 59.18 N2 59
- PV Offset 60
- 6 Interfaces 61
- Endress+Hauser 61 63
- 62 Endress+Hauser 64
- Endress+Hauser 63 65
- 64 Endress+Hauser 66
- Endress+Hauser 65 67
- 8.1 Diagnosis 68
- Endress+Hauser 67 69
- 223EXPHE.CDR 70
- 8.2.2 Disassembly of CPM 223 71
- 8.2.3 Assembly of CPM 223 71
- 8.2.4 Spare parts for CPM 223 72
- 253EXPHE.CDR 73
- 8.3.2 Disassembly of CPM 253 74
- 8.3.3 Assembly of CPM 253 74
- 8.3.4 Spare parts for CPM 253 75
- 8.4 Spare parts orders 76
- 8.6.1 pH/redox transmitter 77
- 8.6.2 pH/mV electrodes 77
- 8.6.3 Assembly 77
- 8.6.4 Liquid KCl supply 77
- 9 Accessories 79
- 10 Technical data 81
- 80 Endress+Hauser 82
- Endress+Hauser 81 83
- 11 Appendix 84
- Endress+Hauser 83 85
- 84 Endress+Hauser 86
- Endress+Hauser 85 87
- 12 Index 88
- PM253E12.CHP 89
- Declaration of contamination 91
- BA 194C/07/en/07.02 92
- Printed in Germany / CV5 / DT 92
Relacionado con productos y manuales para Acondicionadores de aire del sistema de división AUX E&H Series
(15 paginas)
(19 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales