AUX E&H Series Instrucciones de operaciones Pagina 66
- Pagina / 92
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
.
Error
no.
Display Measures
Contakt Error current
Automatic start
of cleaning
Fact User Fact User Fact User
E044
Stability requirement for
calibration not fulfilled
Repeat calibration and renew buffer
solution; replace electrode if necessary,
and check instrument and measuring
cable with simulator.
yes no ——*
E045
Calibration aborted
Repeat calibration and renew buffer
solution; replace electrode if necessary,
and check instrument and measuring
cable with simulator.
yes no ——*
E055
Below main parameter
measuring range
Check measurement and connections;
check instrument and measuring cable
with simulator if necessary.
yes no no
E057
Main parameter
measuring range
exceeded
Check measurement and connections;
check instrument and measuring cable
with simulator if necessary.
yes no no
E059
Below temperature
measuring range
yes no no
E061
Temperature measuring
range exceeded
yes no no
E063
Below current output
range 1
Check configuration in “current output”
menu; check measurement and
connections; check instrument and
measuring cable with simulator if
necessary.
yes no no
E064
Current output range 1
exceeded
yes no no
E065
Below current output
range 2
yes no no
E066
Current output range 2
exceeded
yes no no
E067
Set point exceeded
controller 1
Check configuration. yes no no
E068
Set point exceeded
controller 2
yes no no
E069
Set point exceeded
controller 3
yes no no
E070
Set point exceeded
controller 4
yes no no
E080
Current output 1 range
too small
Expand range in “current output” menu. no no ——*
E081
Current output 2 range
too small
Expand range in “current output” menu. no no ——*
E100
Current simulation active
no no ——*
E101
Service function yes
Switch service function off or switch
instrument off and back on
no no ——*
E102
Manual mode active
no no ——*
E106
Download yes
Wait for download to end. no no ——*
E116
Download error
Repeat download. no no ——*
E152
PCS alarm
Check sensor and connection. no no no
When this error is present, the cleaning function cannot be started.
(Field F8 does not exist for this error.)
Maintenance and troubleshooting Liquisys M CPM 223 / 253
64 Endress+Hauser
- Endress Hauser 1
- Table of contents 3
- 1 General information 4
- 1.5 Product structure 5
- 2 Safety 6
- 2.5 Immunity to interference 7
- 2.6 Declaration of conformity 7
- 3 Installation 8
- 3.2 Dimensions 9
- 3.3 Mounting 10
- PM253E03.CHP 11
- 3.3.2 Mounting examples 12
- Endress+Hauser 11 13
- 3.4 Electrical connection 14
- 131094-4G 15
- Construction of special 16
- CPK1_12e.EPS 16
- Fig. 3.13 16
- • If the software setting 18
- Setpoint 19
- 4.3 Keys 20
- PM253ED4.CHP 21
- 4.5 Operating concept 22
- 4.5.2 Access codes 23
- 4.5.3 Menu structure 23
- • If a change is made but not 23
- • See the appendix of these 23
- 5 Instrument configuration 25
- RELAY2.CDR 26
- Oper.Mode 27
- Glass A5 28
- Fig. 5.4 29
- Alarm signalling and 29
- 28 Endress+Hauser 30
- PM253E5A.CHP 31
- Fig. 5.7 32
- User-defined current output 32
- Sel. Out2 33
- Tabelle (3) 34
- Table (3) 34
- 5.5 Monitoring functions 35
- Rel.Assg 36
- Curr.Assg 36
- CleanTrig 36
- 5.5.2 Check 37
- • Due to its semiconductor 37
- A.Thresh 38
- Err.Delay 38
- LowAlarm 38
- HighAlarm 39
- ProcMonit 39
- Tmax Low 39
- Tmax High 39
- GRENZ-E.CDR 40
- not allowed 41
- Pulse length modulation 42
- Pulse frequency modulation 42
- PM253E5B.CHP 43
- 5.6.4 ChemoClean function 44
- • Use relays 3 (water) and 44
- • When “Economy” is selected 44
- LC PV R2 45
- LC State 46
- 120 R239 48
- 0.3 R2310 48
- Clean = ChemoClean (5) 49
- Neutra controller (6) 49
- ChemoClean (5) 49
- Proc.Type 51
- 5.7 Service 52
- S.Default 53
- Contr E1 54
- SerNo E113 54
- LSG E114 54
- 5.10 Calibration 55
- the user is 55
- ≤ 0.05 and value 56
- 59.18 N2 59
- PV Offset 60
- 6 Interfaces 61
- Endress+Hauser 61 63
- 62 Endress+Hauser 64
- Endress+Hauser 63 65
- 64 Endress+Hauser 66
- Endress+Hauser 65 67
- 8.1 Diagnosis 68
- Endress+Hauser 67 69
- 223EXPHE.CDR 70
- 8.2.2 Disassembly of CPM 223 71
- 8.2.3 Assembly of CPM 223 71
- 8.2.4 Spare parts for CPM 223 72
- 253EXPHE.CDR 73
- 8.3.2 Disassembly of CPM 253 74
- 8.3.3 Assembly of CPM 253 74
- 8.3.4 Spare parts for CPM 253 75
- 8.4 Spare parts orders 76
- 8.6.1 pH/redox transmitter 77
- 8.6.2 pH/mV electrodes 77
- 8.6.3 Assembly 77
- 8.6.4 Liquid KCl supply 77
- 9 Accessories 79
- 10 Technical data 81
- 80 Endress+Hauser 82
- Endress+Hauser 81 83
- 11 Appendix 84
- Endress+Hauser 83 85
- 84 Endress+Hauser 86
- Endress+Hauser 85 87
- 12 Index 88
- PM253E12.CHP 89
- Declaration of contamination 91
- BA 194C/07/en/07.02 92
- Printed in Germany / CV5 / DT 92
Relacionado con productos y manuales para Acondicionadores de aire del sistema de división AUX E&H Series
(15 paginas)
(19 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales